Senin, 04 Juli 2011

Reset Waste Ink Counter Canon Pixma

Reset Waste Ink Counter Canon Pixma i320, i255

Waste Ink Counter Reset.
Langkah 1: Manual for Service mode
1. Lepaskan kabel Power dan USB
2. Tekan dan tahan tombol POWER dan colok kabel POWER
3. Tekan tombol RESUME 2x, kemudian lepas keduanya
4. Colok kabel USB

Manual for Service Mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
7. Connect USB cable
Reset Waste Ink Canon MP160 dan MP145

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off

1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Unplug cable power. (for MP145 / MP150)
6) Turn Off Power. (for MP160)

Error Code :
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error

MERESET WASTE INK COUNTER PADA CANON MP160 DAN MP145
1. Matikan printer (kabel power masih tercolok), tekan dan tahan tombol STOP/RESET kemudian tekan tombol ON/OFF dan lepas STOP/RESET
2. Tahan tombol ON/OFF, tekan tombol STOP/RESET 2x
3. Lepaskan kedua tombol dan printer akan masuk ke SERVICE MODE (muncul angka NOL)
4. Printer akan charging
5. Setelah printer selesai charging, tekan tombol STOP/RESET 4x.
6. Setiap kali tombol STOP/RESET ditekan, lampu ON/OFF akan berubah warna hijau dan oranye.
7. Tekan tombol ON/OFF 1X, angka berubah ke SATU (1)
8. Matikan printer dan cabut kabel POWER.
9. Hidupkan kembali printer

Kode Error Canon MP160 dan MP145
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error


Reset Waste Ink Canon Pixma iP1700, 1880, 1600, 1200, 1300

Kali ini membahas yang namanya cara mereset Printer Canon tipe sejuta umat
Resetter Canon Pixma iP1200, iP1300, iP1500, iP1600, iP1700, iP1880, iP2200

Langkah 1: Masuk ke Service Mode
Matikan Printer
1. Lepaskan kabel Power dan USB
2. Tekan dan tahan tombol POWER, colok kabel POWER
3. Tekan RESUME 2x, lepaskan tombol POWER dan RESUME
4. Lampu akan kedap-kedip beberapa saat, tunggu hingga lampu menyala stabil

Reset Ink Level pada Canon ip1880, MP145, MP530


Hal ini muncul karena level tinta di catrik terbaca habis oleh printer, walaupun tinta di infus masih banyak ataupun barusan di refill.
Untuk mengatasi hal ini cukup guampangggg.... tekan aja tombol RESUME selama beberapa detik (5-8 detik) setelah itu ink level akan ter-reset otomatis dan printer akan meneruskan cetakan.
Hal yang sama berlaku untuk printer Canon ip1200,1300,1600,1700,2200.

Sedangkan untuk tipe Canon MP160, MP145 cukup tekan tombol COLOR untuk mereset ink levelnya...

Untuk tipe multfunction yang lebih tinggi, seperti tipe MP530, MP500, MP830, MP800 (sejenisnya) bisa dengan menekan tombol STOP.


Solusi Error E16 pada Canon seri MP

If you search what's that mean E16 at printer Canon MP Series, the error E16 code is Failed to scan head alignment sheet. I will tell you how to fix the E16, see at below :

- If you see at Printer Status monitor while you printing, you will get the dialog it says your ink is running low.
- So what you need to do? Press the START button, then until 2-3 second press START button again.

I hope that will resolve your problem about error E16.

Kode E16 pada printer Canon seri MP, berarti "Failed to scan head alignment sheet".
Saya akan mencoba memberitahu anda bagaimana memperbaiki E16 ini.

* Perhatikan Status Monitor pada printer anda, akan muncul pernyataan bahwa tinta akan habis (Ink is running low)
* Yang harus anda lakukan adalah tekan tombol START, kemudian tunggu 2-3 detik kemudian tekan lagi tombol START.

Reset Waste Ink Canon Pixma iP1000

Canon PIXMA iP1000
Waste Ink Counter Reset.
Langkah 1: Manual for Service mode
1. Lepaskan kabel Power dan USB
2. Tekan dan tahan tombol POWER dan colok kabel POWER
3. Tekan tombol RESUME 2x, kemudian lepas keduanya
4. Colok kabel USB

Step 1 : Manual for Service Mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.
7. Connect USB cable

Reset Waste Ink Canon MPC 190

Canon MPC190
Reset Waste Ink
1) Masuk ke SERVICE MODE.
dengan menekan Menu, Copy, Scan, Copy, Copy (tekan saja urutan tombolnya, jgn ditahan)
2) Pilih TEST MODE.
3) Pilih [8] PRINTER TEST in TEST MODE.
4) Pilih 3. [EEPROM CLEAR].
5) Piliht 0. [INK COUNT].
6) Tekan tombol [Set]
7) Tekan tombol [Stop/Reset] , kemudian tekan tombol [ON/OFF]

Tidak ada komentar:

Poskan Komentar